Tuesday, August 31, 2010

Ball Mill Control Theory and Application

Note: Cross posted from sbmzhcn.

Permalink: http://sbmzhcn.appspot.com/2010/09/1/265001.html

1 The principle of automatic control system for milling process overview

Automatic control of the ball grinding mill powder size of purpose is to control the ball mill, the possible to improve the quality of products of powder. Using the computer control system of the grinding technology can improve the productivity, improve the control accuracy.

1.1 The principle and operating characteristics of ball mill

Usually the ball within a ball. Wall lining has wavy manganese steel armor of cylinder. Cylinder side as raw materials imported and wind blowing on the other side of the import, export for gas mixture of powder. The motor and reducer cylinder rotate speed, turning device with centrifugal and polishing in under the action of forces, armor will ball and raw material up to a certain height. Then use gravity free fall. Raw materials are mainly ball shatter, but also affected by steel ball and armor between, between the extrusion and grinding. A good FenZi grinding materials, mixing system into the next procedure. For running after a ball. Noise signal, the population pressure difference and relationship between output (see figure 1)

ball-mill-work

When the ball when the increase in quantity. The increasing power of ball mill, but until the noise signals, basically is found by large slope down. With the increasing of quantity of ball mill, export differential pressure also slightly increased. When feed greater depth. Differential pressure is rising sharply.

According to the curves shown in figure 1 characteristics can be seen. The noise signal is ball mill can reflect the quantity of materials. In the ball speed constant, the ball is a certain period, by measuring the grinding machine, the noise signal can be directly within the ball mill detection of materials. Therefore, the stability of the grinding machine for shoes. Control air purging, make their relationship, it can control the equilibrium of the grinding mill.

1.2 Difficult to control the ball milling

1) from its existing mill run characteristics. Noise is a variation of parameters, it is significant for mill materials. But because the ball inside the operating conditions of complex and measurement methods have greater error. So the control scheme in composition may have some limitations.

2) the grinding mill control system is more people, more than the output variables and strong coupling, large inertia, large delay of time-varying system. Using common PID control force lacerates the relationship between the variables. Not only get better effect, but also is caused extremely easily system stability.

3) the grinding ball control, except for shoes, accused of parameters for air outside disturbance. Also, the grain size ball and the effect of water content.

2 Grinding process is sub

General grinding system operating first kind is to use of ball mill for export pressure difference control parameters, the second kind is to use manual operation. Depend on the experience, the operator control over two methods, the existing control precision grinding low volatility of particle size, quality and yield of grinding is difficult to control. The quality of products.
Two of the automatic control system

Control system is composed of two parts, hardware and software are introduced as follows:

2.1 control system software

The software is used to control strategy of human-simulated intelligent control scheme. It is based on the principle of intelligent control, imitation of man's thinking on intelligent decoupling, ball mill in order to ensure the safe and reliable operation, the software is the core logic by intelligent controller and intelligent algorithm.

Intelligent design according to the logic is running the operation experience, according to the input error and its variation formulate corresponding control strategy, the principle is: (1) the noise signals according to the ball, adjusting control of disc feeder under shoes. Make quantity to achieve stability.

(2) adjust air control two loop baffle, its balance. Intelligent algorithm according to the ball mill system controller is the coupling, the controller can be divided into three sons, each loop circuits using intelligent algorithm based on the input, and the changes of choose corresponding algorithm and achieve the purpose of humanoid control.

ball mill

2.2 control system of the hardware

Control system hardware consists of: PLC and computer, isolation and transducers, inverter, noise and transform device, flowmeter, electric baffle valves, electric butterfly valve, pressure transmitter such equipment. A new form of the control system can fully test the key parameters of grinding process, through these parameters to PI C and computer provide enough information to control system, comprehensive treatment, and to form a correct judgment, provide accurate control signal, make grinding system according to the requirements of control in advance to work.

Types of crushers-jaw crusher machine

jaw crusherJaw crusher  is a widely used stone crusher. jaw crushers are configured for primary crushing of even hardest rock. Our jaw crushers are crushing without rubbing minimum dust oil lubrication, devise having oil or grease lubrication system. SBM crushers are designed for long life service with minimum maintenance for hard, tough, abrasive material and overload high capacity. This service goal has been confirmed by our customers all over the world.

A jaw or toggle crusher consists of a set of vertical jaws, one jaw being fixed and the other being moved back and forth relative to it by a cam or pitman mechanism. The jaws are farther apart at the top than at the bottom, forming a tapered chute so that the material is crushed progressively smaller and smaller as it travels downward until it is small enough to escape from the bottom opening. The movement of the jaw can be quite small, since complete crushing is not performed in one stroke. The inertia required to crush the material is provided by a weighted flywheel that moves a shaft creating an eccentric motion that causes the closing of the gap.

Single and double toggle jaw crusher are constructed of heavy duty fabricated plate frames with reinforcing ribs throughout. The crushers components are of high strength design to accept high power draw. Manganese steel is used for both fixed and movable jaw faces. Heavy flywheels allow crushing peaks on tough materials. Double Toggle jaw crushers may feature hydraulic toggle adjusting mechanisms.

Flexible discharge opening setting of jaw crusher allows perfect match with relative equipments.  jaw crusher is easy to install, operate and maintain. As per Feedback, our experts will make continuous improvements on our products to meet customers' changing needs. Jaw crusher is widely used in fields of mining, metallurgy, construction, smelting, hydropower and chemical industries etc.
Features:
1. The application of world-class manufacturing processes and high-tech materials.
2. Integrated steel structures are used for the base of bearing;
3. The broken cavity using "V"-shaped structure, so that the actual width of feed is same as nominal width;
4. The broken cavity is deep and without dead zone, increased capacity and output feed;
5. Lubrication system is safe and reliable, convenient of replace parts, easy to maintenance;
6. The outlet employs pad-style adjustment devices, convenient and reliable, and increase the flexibility of the equipment;
7. Low noise, less dust;

Monday, August 30, 2010

What is a vertical roller mill

Vertical 

roller mill

Vertical roller mill ( grinding ) is the dawn of Heavy Industry and Technology to address the industrial mill output is low, energy consumption and higher technical problems, absorb advanced technologies combined with our years of design and manufacture of advanced mill concept and market demand, after years of concentrated design improved Large grinding equipment . Vertical roller mill using reasonable and reliable structural design, with advanced technological process, set drying, grinding, powder selection, improve the integration, especially in the large grinding process, can meet customer demand, the major technical, economic indicators reached the international advanced Level .

Vertical roller mill applications
  • Special glass fiber industry ‘s largest high yield pyrophyllite powder fineness of grinding ;
  • Private coal gangue powder industry powder produced a large output ;
  • Special chemical industry raw materials, high production of various chemical powder production;
  • Non-metallic mineral industry, a variety of low, medium and high hardness of the hundreds of species of large-scale ore powder production preparation;
  • Hundreds of species of other big industry production of a variety of materials, powder preparation;
Vertical roller mill Features:
  • operating costs low:
    1. mill efficiency, vertical roller mill with roller compacted ground and feed bed materials, low energy consumption, milling system power consumption 40-50% lower than the milling system, and with the increased humidity of raw materials, section Electric effect is more significant.
    2. metal loss, liner and roller with a special material, long life, reduced operating costs, high utilization ;
    3. into the grinding material particle size of up to roller diameter of about 5%, usually 40 ~ 100 mm, it can be saved two medium-sized vertical mill grinding.
  • construction costs low:
    1. The grinding process is simple, and milling system can be reduced compared to an area of about 50%, reduced by about 70% of construction costs, building size, occupy less space .
    2. set of broken grinding, drying, grinding, grading conveyor in one, the system is simple, compact . Can open layout, making low-cost construction .
  • easy and reliable operation :
    1. with a control device, can realize remote control, easy to operate .
    2. The roller cover and the disc has to prevent direct contact liner quality control device, to avoid fragmentation of severe vibration .
  • drying ability, vertical mill using air transportation of materials, the grinding of materials for large water inlet temperature can be controlled so that products reach the final water, drying in the grinding of water up to within 12 to 15 % of the material, even drying Dry milling, drying only water for 3 to 4 % of the material .
  • stable quality, uniform particle size distribution . Material in the mill residence time is short, easy-to- size and chemical composition of the product testing and control, product quality and stability .
  • easy maintenance, through the maintenance tank, turn rotating arm, roller, liner can be replaced in a very short time .
  • environmental protection, energy saving ; vibration, low noise, low dust, clean operating environment to meet the requirements of environmental protection .

Source Article:http://sbmzhcn.appspot.com/2010/08/31/245002.html

ball milling machine how to use

A ball mill is used to grind solid materials into powders. It's commonly used to make paints and ceramics. It rotates on a horizontal axis and uses iron or stainless steel balls to crush materials into powder. With a container and a power drill, you can quickly make your own ball mill.

first,Installation Ball Mill
      The quality of ball mill installation quality, the ability of mill is the key to normal work. Various types of ball mill installation method and sequence similar. To ensure the smooth functioning of ball mill and reducing the harm to the buildings, it must be installed in its weight of 2.5 to 3 times the reinforced concrete foundation.

      Installation ball mill, the first should be installed main bearing. In order to avoid aggravating the problem of the hollow crankshaft bearings lining and shoulder wear, the two main bearing the base plate of elevation difference in the length of each meter should not more than 0.25 mm. Secondly, the installation of the ball mill cylinder of the light of the specific conditions, can be pre-assembled the entire English Department loaded directly, but also can be divided into several parts of the installation, adjustment and should check with the centerline Journal and the ball mill, the error must ensure that its Concentric within per meter in length should be less than 0.25 mm. The final installation of the transmission components (small gear, uranium, coupling, reducer, motor, etc.) During installation, product technical standards should be measured and adjusted. Gear check the radial pendulum poor and small gear meshing performance; gear reducer and small concentric degrees, and the motor and reducer concentric degrees. When fully installed are in line with requests, we can not go on the basis of bolt main bearing floor and the last watering.

Second, Operation and maintenance of ball mill

    If the ball machine running high rate of grinding effect, and to strictly abide by the operation and maintenance of order. Starting in the ball mill, should check whether the tightening bolt connections; gears, coupling, etc., as well as the keys to the first mine-spoon Solid tight situation.

    Check the oil tank reducer and the adequacy of the lubricating device and instrumentation whether illnesses, pipes unimpeded. Check ball mill with classifier equipment availability impede functioning of the surrounding debris, and then use the cable car to the ball mill-week, the ball loose tube Dutch and ores, and to inspect the ring gear and pinion meshing, there abnormal sounds. The start order is first activated ball mill lubricants pump, when the hydraulic reach 1.5 to 2.0 kg / cm 2 o'clock, the ball mill will be allowed start again start classifier. Everything is running normally, and so on, can begin to draw mine. In operation process, should always pay attention to bearing temperature should not exceed 50 ~ 65 ° C. The attention to the regular motor, voltage, current, temperature, audio, and so on. Attention lubrication system at any time, the oil tank should not exceed 35 ~ 40 ° c, to tubing pressure should be maintained at 1.5 to 2.0 kg / cm 2. Check size gear, the main bearings, such as grading machine transmission components reducer lubrication, and attention to the observation before and after the ball mill Cover, Simplified and exclusive ore bins overflow tank and machine classification back to the trough of sand plug the leak and sand. Regular attention to the changing nature of ore, according to the situation promptly and take appropriate measures.

     Stop ball mill, the first stop to the mining machine, within the ore processing to be simplified after the end of ball mill motor to stop, the last stop pumps. With the upgrade installations classifier to the spiral of sand, and then stop classifier.

Sunday, August 29, 2010

Crusher working principle and advantages of an overview analysis

Note: Cross posted from sbmzhcn.

Permalink: http://sbmzhcn.appspot.com/2010/08/30/235002.html

I. Impact Crusher  Work The name suggests, Impact Crusher is used to achieve the crushing effect of counter-masterpiece, and in large materials into the counter board and after the crushing chamber between the rotor by rotation of the rotor part of the role of access to kinetic energy in the counter plate and the rotor repeatedly between the impact of each of the two first-class counter-cavity, the second-level counter chamber and the bottom of the grinding chamber of progressively broken, meet the requirements of the expected size.

II crusher  hammer crusher compared with the technological advantages of
1. Able to handle large moisture content of materials, to prevent clogging crusher
Excessive water in the processing of materials, the impact crusher the feed chute and the counter plate can be equipped with heating devices to prevent the bonding material. Impact Crusher is no need with the bottom of the sieve can prevent clogging. The hammer crusher can not be used heating methods to prevent adhesion of materials, and should be equipped with the bottom of the sieve plate, increasing the possibility of blockage.

2. Impact Crusher is suited to the soft material has applied to the material hardness of very large

Board crusher hammer strong mechanical clamping structure is scheduled for the rotor, when the rotor rotates with great inertia. Relative to the hammer crusher (hammer was hanging state), impact crusher rotor has a greater momentum, to adapt a more rigid material broken at the same time, lower energy consumption.

3. Can facilitate flexible adjustment of the particle size, wide tuning range
Counterattack breakers are many ways to adjust the particle size, such as adjusting the rotor speed, conditioning and grinding chamber counter plate and gap. Gap adjustment can be mechanical or hydraulic adjustable, hydraulic adjustment system can easily operate the button or fortune through the local control system to complete the gap adjustment. The hammer crusher adjust the particle size can only be achieved by replacing the bottom of the sieve.

4. Consumable wear little more than hammer crusher, metal high utilization
Impact Hammer wear only one side in Looking materials. When the rotor speed is normal, the feed will drop to the plate hammer surface (of attack), hammer on the back and side panels are not being worn. Even Looking material this side very little wear. And the bottom of the grinding rod is also very easy to replace. Impact Hammer metal utilization up to 45%? 48%. The hammer crusher hammer was hanging state, the wear occurs, the front and rear and side, relative to the plate hammer, hammer wear more serious, hammer metal utilization ratio is only about 25%. And the rotor body itself may also be worn. Hammer crusher wear badly affected by the bottom screen, grille to replace all, and replace the sieve of the work more complicated.

5. Easy replacement of spare parts, less maintenance costs
Crusher rotor only hammer to install six panel, using special tools provided by the plate hammer easily replaced, the replacement of a board of only one frequency hammer time. The bottom of the rod mill grinding chamber also requires only the replacement of dozens of minutes, greatly reducing maintenance and maintenance time and costs. The hammer crusher hammer up to 100 only, changing to a hammer a lot of time and manpower, repair and maintenance costs higher. Replacement of the bottom screen is also extremely cumbersome. Fortune

above content is based on years of experience in production machinery and customer feedback, summary income information purposes only. Although the impact crusher with high technical advantages, but when you select the crusher is recommended that you first expert advice, depending on your situation to choose the most suitable crushing machine (such as jaw crusher, hammer crusher , impact crusher, etc.), lower production costs.